12-inch Milled Gray Horizon with tapered-back sawn ends: terraced project wall below a home

Sunset Stone blog

How to Build a Natural Stone Retaining Wall

A step-by-step guide to building a natural stone retaining wall with quarried limestone block: base prep, drainage, stacking, backfill and compaction.

Sunset Stone Company · 2026-11-10

Before you build: important notes. This article is general guidance for planning a natural stone retaining wall, not engineering, legal or site-specific advice. Check local codes and permits, call 811 before you dig, and have taller or loaded walls reviewed by a licensed engineer or qualified contractor. Sunset Stone supplies the stone and does not design or install walls. Read the full notes.

A natural limestone block retaining wall built from quarried block is a gravity wall. It holds soil back with its own weight, so the stone only performs as well as the base under it and the drainage behind it. This is the sequence professional installers follow.

If you are still choosing a product, measuring the wall, or planning a delivery, start with how to plan a limestone retaining wall. That page is the ordering brief. This post is the build sequence your installer will actually run on site. Sunset Stone supplies the stone. We do not design or install the wall.

The same steps apply when a crew is building a boulder-style wall or an outcropping stone wall with large limestone. We do not sell boulders as a separate product. Sundown Ledge (Ranch), 14" Premium (Estate, including wides), and other large wall stone are what crews use for that look. Irregular stone simply takes more time to fit at each course.

1. Check the rules before you dig

The model building codes used in most of the United States, the International Residential Code and the International Building Code, exempt most retaining walls that are not over 4 ft tall from a permit. That height is measured from the bottom of the footing, not from finished grade, and the exemption disappears when the wall supports a surcharge such as a driveway, a slope, a fence or a structure [1][2].

Cities often tighten that rule. Phoenix and San Diego use a 3 ft threshold, measured from the top of the footing, and Menlo Park uses 2 ft [3][4][5]. Call your building department first, and call 811 to have utilities located. Do you need a permit or an engineer for a retaining wall? covers the measurement, surcharge and engineering tests in more detail.

2. Excavate the base trench

Start at the lowest point of the wall and work uphill. A common manufacturer standard is a trench about 24 in. wide, deep enough for 6 in. of base plus the buried portion of the first course, with roughly 1 in. of extra embedment for every foot of wall height [6].

Remove all topsoil, roots and organic material. None of it can be reused as backfill [6]. If the bottom of the trench is soft, wet or heavy clay, dig it out and replace it with granular material compacted in lifts of 8 in. or less [6].

3. Build the leveling pad

Place at least 6 in. of clean crushed stone in the trench, compact it, and check it for level along the full length [6][7]. Where grade changes along the wall, step the pad up in level sections. Do not slope it.

4. Set the base course of the limestone block retaining wall

The first course decides how the rest of the wall goes. Level every stone front to back and side to side, because small errors at the bottom grow with each course above [6]. Use your largest, most uniform pieces here.

This is where milled limestone shows its value on a job. Sunset Stone planes the tops and bottoms of its double-sided milled stone to a 12¾ in. thickness, held within about 1/4 in. That tight tolerance is the point: each course sits flat on the one below, the crew spends less time shimming, joints stay tight, and the wall goes up faster. The face is never milled. It is left natural.

Single-sided milled stone (Signature) has one bed planed and the other left natural, and is held within about 1/2 in. You still get a flatter bed than fully natural ledge, with less fitting at each course, though it is not as uniform as the double-sided 1/4 in. product, and it costs less than double-sided. Milled stone with sawn ends (Heirloom+) is the same milled limestone with the meeting ends sawn tapered back for a tight run.

By comparison, 14" Premium Natural Tan and 14" Gray Horizon (Estate), which are geologically a Dover Ledge, keep natural tops and bottoms, with about 1 in. of natural variance, plus or minus. The 14 inches is course height, how tall each row stands, not bed depth. Those pieces have the character of natural ledge and outcropping stone. They simply take more care to set level than milled block. See also 14-inch limestone retaining wall stone.

Pieces typically weigh 800 to 2,000 lb, so plan on setting them with a machine equipped with forks or a thumb.

Milled limestone retaining wall block stacked in level courses with sawn ends
12-inch Milled Gray Horizon with tapered-back sawn ends, stacked in level courses.

5. Install the drainage

Lay a 4 in. perforated pipe at the base behind the first course, sloped so it drains by gravity, with an outlet at the low point and at least every 50 ft [8]. Then keep a zone of clean 3/4 in. crushed stone at least 12 in. wide behind the wall as it rises [6][8]. Retaining wall drainage: why walls fail and how to prevent it covers the pipe, the backfill and filter fabric in detail.

6. Stack, stagger and batter

Offset the vertical joints from course to course so no joint runs straight up the wall [6]. Lean the wall back into the slope as you build. For structured stone walls, landscape architects typically call for 1 to 2 in. of batter per vertical foot [9].

Use sawn ends, sawn tapered back, where stones meet in the run of the wall for tight joints. Use natural ends at wall ends and returns.

7. Backfill and compact every course

Backfill and compact after each course, not at the end. Keep lifts to 8 in. or less [6]. Keep heavy equipment at least 3 ft back from the wall and use a walk-behind plate compactor in that zone [10]. On engineered walls the usual target is 95 percent Standard Proctor density [8].

8. Finish the grade

Shape the ground above the wall so surface water runs away from it. Route downspouts and irrigation somewhere else. Water that never reaches the wall is water the drain does not have to handle.

Sundown Ledge gray limestone retaining wall with steps
Sundown Ledge gray used as large stacking rock for a natural stone wall with steps. We do not sell boulders as a separate product. Crews build that look with large ledge stone like this.

When to bring in an engineer

Bring in a licensed engineer for walls over 4 ft, terraced walls, slopes above or below the wall, any surcharge, or poor soils [6][1][11]. How tall a gravity wall can go, and when geogrid enters the picture, is the subject of Gravity wall or geogrid: how tall can a retaining wall go?. For the choice between planed courses and natural 14" ledge, see milled limestone vs natural ledge. Permits and the 4 ft rule are covered in Do you need a permit or an engineer for a retaining wall?. Drainage and base prep are in Retaining wall drainage: why walls fail and how to prevent it.

Stone and freight are quoted from the product type and the delivery ZIP. We can also walk through options on the delivery page. For the briefing on course height, tonnage and who builds the wall, see how to plan a limestone retaining wall.

References

  1. International Residential Code (2021), Section R105.2, Work exempt from permit (public reprint)
  2. International Building Code (2021), Section 105.2, Work exempt from permit
  3. City of Phoenix, Required Permits for Fences and Retaining Walls
  4. City of San Diego, When is a Permit Required?
  5. City of Menlo Park, Work Exempt From Building Permit
  6. Allan Block, How to Install a Retaining Wall: Basic Installation
  7. RCP Block & Brick, How to Build a Retaining Wall
  8. Ideal Concrete Block, A Contractor's Guide to Installing Segmental Retaining Wall Systems
  9. American Society of Landscape Architects, Dry Stacked Stone Walls
  10. Allan Block, Residential Landscape Retaining Wall Guide (PDF)
  11. International Residential Code (2021), Section R404.4, Retaining walls (public restatement)

Before you build: important notes

The information in this article is general guidance for planning a natural stone retaining wall. It is not engineering, legal or site-specific advice. Building codes, permit rules and setback requirements vary by state, county and city, so check with your local building department or municipal authority before you start. Get any required permits.

Call 811 or visit Call811.com at least a few business days before any digging so underground utilities can be marked. This free service is required by law in most states. In Kansas, you can also reach Kansas811.

Soil type, compaction, drainage and regional conditions such as clay, frost depth and groundwater all affect how a wall performs. A wall that works well on one site may not work on another. Walls over 4 feet tall (measured from the bottom of the footing), walls holding back a slope, driveway or structure, and walls near property lines or water should be reviewed by a licensed engineer or qualified contractor.

Sunset Stone supplies the stone and does not design or install walls. Any installation is done at the owner's and installer's discretion and risk. Always follow safe lifting practices and wear proper protective equipment when handling stone.

Text product type and zipcode for pricing! (785) 340-0301

Or call (785) 340-0301 · email info@sunsetstoneco.com. We deliver the stone. We do not design or install the wall.

You can also request a quote on the contact page.

All blog posts · Guides · Stone products · Contact

Pricing

Text product type and zipcode for pricing! (785) 340-0301

Tell us the product type and your delivery ZIP. We'll come back by the next business day with stone and freight, the whole number, not a teaser. We deliver the stone. We do not design or install the wall.

Call (785) 340-0301
Mon–Fri 8:00 am – 4:30 pm Central
Email info@sunsetstoneco.com

Fields marked * are required. A phone number or an email is enough.

Call (785) 340-0301Get a Free Quote